Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Beverly Hills, CA
Gate access control in Beverly Hills means working on systems tied to custom estate gates, often built into 1920s-1940s Spanish Colonial or Tudor properties south of Sunset, or mid-century parcels in Trousdale Estates. The work here is different because most properties run bespoke ornamental iron or steel gates with intercoms, keypads, and license-plate readers that were never off-the-shelf. When a keypad stops talking to a motor, or a phone entry system stops tripping the relay, the fix usually requires matching newer electronics to older gate hardware and wiring. Call (424) 321-7416 and we’ll send a technician who documents every setting before and after.
Why Beverly Hills Homes Are Different
Beverly Hills has the highest concentration of custom automated estate gates per square mile of any U.S. city. In Trousdale Estates and the Benedict and Coldwater Canyon corridors, steep driveways force cantilever slide gates instead of swing gates, and those slides develop their own set of track, roller, and motor-alignment failures. South of Sunset, the 1920s-1940s Mediterranean and Spanish Colonial estates often retain original wrought-iron gate panels retrofitted with modern operators, so structural repairs demand period-matched metalwork. Santa Ana winds in the fall slam heavy swing gates against their stops, snapping aging weld points and knocking operators out of alignment. And Beverly Hills runs its own municipal permit office, separate from the City of Los Angeles, with notably strict UL 325 entrapment-protection enforcement on any gate operator replacement or structural repair.
Our Main Beverly Hills Services
Beverly Hills homeowners call most often about two things: a gate that won’t open or close, and a motor that runs but doesn’t move the gate. We also build and install new gates, and service or replace motors and openers on existing ones.
Gate Repair in Beverly Hills
Most repair calls in Beverly Hills involve a gate that’s stuck, sagging, or slamming against its stops after a Santa Ana wind event. Older welded joints on custom ornamental gates fail under repeated wind loading, and the damage is rarely visible until the gate stops moving. We repair the member in place where possible and match the metalwork so the fix isn’t obvious. For anything structural, we handle the Beverly Hills permit requirements and document the work photographically. Gate Repair in Beverly Hills
Gate Installation in Beverly Hills
New gate installations in Beverly Hills usually mean a custom swing or cantilever slide gate sized to an existing driveway, often with period-appropriate ironwork for older estates. We measure the opening, check the grade and the setbacks, and produce a written scope and price before any fabrication starts. Steep canyon driveways off Benedict and Coldwater call for slide gates that ride above the grade, and we build those to match the house, not the catalog. Gate Installation in Beverly Hills
Gate Motor & Opener in Beverly Hills
When a motor runs but the gate doesn’t move, or the opener loses its limits and reverses at the wrong point, the fix is usually a reset, a limit-switch adjustment, or a motor replacement if the gearbox has failed. We service LiftMaster, FAAC, BFT, Linear, and five other major automation brands, so we work on whatever motor is already on the property rather than steering you toward a replacement. Every opener job gets a photo record of the settings and the part numbers. Gate Motor & Opener in Beverly Hills
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Before
AfterGate Access Control in Beverly Hills
Access control in Beverly Hills means the keypads, intercoms, phone entry units, card readers, and video systems tied to custom estate gates. Many of these systems were retrofitted onto 1920s-1940s gates, so the wiring is old, the voltage is low, and the relays are hidden inside stucco columns or iron posts. When a code stops opening the gate, it’s usually a low-voltage wiring fault or a failed relay, not the gate itself. Our Gate Access Control service covers the electronics, the wire runs, and the documentation, so the next technician doesn’t have to reverse-engineer what we already mapped.
Keypad Entry
Signs you need it
Codes that work intermittently, or a keypad that lights up but doesn’t trip the gate.
What it costs in Beverly Hills
Keypad replacement and reprogramming in Beverly Hills typically runs $215-$360.
How we do it
We meter the keypad, test the relay, replace or reprogram the unit, and photograph the wiring in place.
Video Intercom
Signs you need it
Audio that cuts out, no picture at the monitor, or a call button that doesn’t ring the house.
What it costs in Beverly Hills
Video intercom troubleshooting and component replacement runs $260-$540 depending on cabling and panel condition.
How we do it
We trace the station wiring, identify the failing module, replace it, and leave a labeled photo record of the reconnections.
What Gate Access Control Costs in Beverly Hills
| Item | Typical range in Beverly Hills |
|---|---|
| Keypad replacement / reprogram | $215-$360 |
| Video intercom repair | $260-$540 |
| Low-voltage wiring diagnosis | $140-$260 |
Can you integrate an old intercom with a new smart-home system?
Usually yes, but it depends on the existing wiring and the protocol the house system uses. We test the conductor count and voltage first, then match a relay or adapter that talks to both ends. Call (424) 321-7416 and we’ll tell you what’s possible after a site check.
Why does my keypad work sometimes and not others?
Intermittent keypad faults in Beverly Hills are usually low-voltage wiring issues, often from heat-dried insulation or a relay with burned contacts. We meter the circuit, identify the failing segment, and replace only what’s bad. Call for a written diagnosis.
Gate Parts & Welding in Beverly Hills
Parts and welding in Beverly Hills cover the structural hardware: hinges, posts, rails, rollers, and the custom fabrication that keeps a one-of-a-kind gate square and moving. Older estate gates from the 1920s-1940s carry original wrought-iron panels that need period-matched metalwork, not a replacement rail from a catalog. Our Gate Parts & Welding team fabricates, welds, and finishes on site where possible, and documents the part numbers and bead locations before we leave.
Hinge Replacement
Signs you need it
A gate that sags at the latch side or scrapes the driveway when it swings.
What it costs in Beverly Hills
Hinge replacement in Beverly Hills usually falls between $165-$350 per hinge including fabrication.
How we do it
We block the gate, cut the old hinge, weld or bolt in a matched replacement, and photograph the final position.
Gate Rollers
Signs you need it
A cantilever slide gate that shudders, binds, or squeals along the track.
What it costs in Beverly Hills
Roller replacement runs $210-$460 depending on the roller size and track condition.
How we do it
We lift the gate off the track, swap the worn rollers, check alignment, and record the new clearances.
What Gate Parts & Welding Costs in Beverly Hills
| Item | Typical range in Beverly Hills |
|---|---|
| Hinge replacement | $165-$350 per hinge |
| Roller replacement | $210-$460 |
| Custom welding repair | $180-$550 per repair |
Can you match the original ironwork on a 1930s gate?
Yes. We match the stock profile, the joinery style, and the finish so the repair doesn’t read as new work. Most Beverly Hills estate gates were hand-forged in place, and we account for that in our fabrication. Call (424) 321-7416 for a written estimate.
Do I need a permit for structural welding on my gate?
For structural repairs and operator changes, Beverly Hills code enforcement often requires a permit, and the inspectors check UL 325 compliance on entrapment protection. We handle the permit paperwork and the inspection coordination. Call to have a technician confirm what your gate needs.
Brands We Service in Beverly Hills
We service Mighty Mule, LiftMaster, FAAC, and BFT openers, along with five other major automation brands, and we stock the common boards, relays, and safety edges for same-day replacement on most Beverly Hills service calls. Documented part numbers on every visit mean no guesswork later. See our brands for the full list.
Pricing for Gate Repair in Beverly Hills, CA
| Service | Typical range in Beverly Hills |
|---|---|
| Keypad replacement / reprogram | $215-$360 |
| Video intercom repair | $260-$540 |
| Low-voltage wiring diagnosis | $140-$260 |
| Hinge replacement | $165-$350 per hinge |
| Roller replacement | $210-$460 |
| Custom welding repair | $180-$550 per repair |
Prices push upward in Beverly Hills when a gate needs period-matched ironwork, when the driveway grade calls for a cantilever slide with custom rollers, or when the access-control wiring is original to the property and needs full tracing. Every price is written and handed to you before we start, under our Haven Standard.
Neighborhoods We Serve in Beverly Hills
We work across Beverly Hills, from the flats south of Sunset to the canyon drives off Benedict and Coldwater. Typical response time for a gate emergency in Beverly Hills is under 90 minutes when you call (424) 321-7416.
- Trousdale Estates
- Benedict Canyon
- Coldwater Canyon
- The Flats south of Sunset
- Beverly Hills Gateway
Service Area - Cities Near Beverly Hills
We also serve the surrounding cities with the same written-price, photo-documented service. West Hollywood, CA, Studio City, CA, Culver City, CA, and Sherman Oaks, CA all fall within our service area.
Serving Beverly Hills, CA - Our Local Coverage Area
We’re based in the Beverly Hills area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Beverly Hills
For gate emergencies, we typically arrive within 90 minutes anywhere in Beverly Hills. A live person answers (424) 321-7416 around the clock, so you’ll speak to a dispatcher, not a voicemail, when the gate fails late or on a weekend.
Beverly Hills has its own municipal permit office and its inspectors enforce UL 325 entrapment-protection compliance strictly. Opener replacement and structural repairs often need a permit, and we handle that paperwork as part of the job. Call for a written scope.
Yes. Every job gets a written price before any tool is picked up, exactly as our Haven Standard requires, and the final invoice will not exceed that number. You’ll also receive a photographed record of what was found and what was installed.
If your Beverly Hills gate isn’t opening, closing, or listening to the keypad, call (424) 321-7416. A live person answers, a named technician arrives with the price already in writing, and the work is documented photographically before we leave.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Beverly Hills Customers Say
"They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N."Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R.