Linear Gate Installation Nationwide

Linear Gate Installation in West Hollywood: What to Know First

Linear gate installation in West Hollywood typically runs between $1,850 and $6,400 depending on whether you’re putting in a new operator on an existing gate, building a full driveway gate from the post up, or replacing an aging Linear board and motor assembly. Most single-operator Linear installs on a prepared gate are done in one day. We are an independent Linear service provider, not an authorized dealer, which means we stock parts from multiple suppliers and price the job in writing before any tool comes off the truck.

Call (424) 321-7416

If you own a Linear opener and the gate is dead, half-cycling, or was never installed right in the first place, this page tells you what we find, what it costs, and what you get when we leave. Call (424) 321-7416 and a live person answers. No callback queue.

How Linear Products Fail - and How We Fix Them

• Linear LDO50 and LDO33 swing-arm operators: the limit cam assembly drifts. These residential swing operators use mechanical limit switches behind the cover. Over time, in West Hollywood’s dry heat, the plastic cam lobes develop hairline cracks and the switch reads the gate’s travel point 8 to 15 degrees off. The gate stops short of closed or slams into the post. We open the housing, photograph the cam position, replace the cracked cam set, and re-run the full travel calibration with the gate under load.
• Linear VS-GSLG sliding gate operator: the chain tensioner backs off. This is the most common sliding-gate failure we see on hillside properties in the Hollywood Hills West area. The take-up bolt vibrates loose over months of daily cycles, the chain sags, and the operator’s internal gear starts skipping teeth. If you hear a sharp clack when the gate starts moving, that’s usually a jumped chain link. We reset the tension to manufacturer spec, add a jam nut where Linear didn’t, and photograph the final chain sag measurement.
• Linear APeX and MegaCode receivers: ghost remotes and no-code situations. These receivers sit on the 318 MHz band and are prone to interference from nearby apartment building gate systems in denser parts of West Hollywood. The symptom is simple: your remote works at arm’s length but not from the street, or a neighbor’s remote opens your gate. We do a frequency scan, re-seat the antenna, and if needed swap in a fresh MegaCode receiver with wiped and re-learned remote codes, then document the remote count in your file.
• Linear M3 and M5 series gate openers on old steel gates: dead capacitors after brownouts. West Hollywood’s older residential streets see voltage dips during summer peak loads. Linear’s AC motor start capacitors take the hit. The gate hums but won’t move, or trips the breaker. We test the capacitor with a meter, not by guess, and replace it with an OEM-spec unit. If the capacitor has leaked, we clean the board housing and photograph the corrosion before it eats a trace.
• Linear DC board failures on gates wired by non-gate electricians. We regularly follow up behind general electricians who wired a Linear operator like a garage door opener. The board is not rated for continuous-duty cycle but the gate is. The relay burns out within 18 months. We replace the board, correct the wiring to Linear’s proper gate diagram, and leave you a printed copy of both the wiring diagram and the photo record of every terminal connection.

Our Linear Gate Installation Process

1. 1
   We walk the gate and the operator in place. Before quoting anything, we test the full stroke of the gate, the operator’s current draw, the limit settings, the safety edges or photo-eyes, and the condition of the hinges and wheels. If there’s an existing Linear unit, we open it and photograph the board, the wiring, and every setting we find.
2. 2
   We hand you a written price. Not a range, not a “depends on what we find.” The number is on paper before work starts. That’s Clause 1 of The Haven Standard, and it’s non-negotiable on our end.
3. 3
   We make the parts call with you. Some Linear parts are only worth buying OEM, especially control boards and limit switches. Others, like chain, brackets, and some capacitor types, are fine as quality aftermarket. We show you the difference and let you decide, with the price difference on paper.
4. 4
   We do the installation and document it. On a full Linear install we mount the operator, set the limits to manufacturer spec, wire the safety circuit, run the full open/close cycle at least ten times, and photograph the final state of every adjustment.
5. 5
   We test, then hand you the record. You get a photo log of what was found, what was set, and what was installed, plus a written note with the model number and any part numbers we used. That’s Clause 4.
6. 6
   You get the 365-Day Done Right Promise. If anything about the install isn’t right within one year, we come back and make it right at no charge. No argument, no fee, no expiration date inside that window.

Before

After

What Linear Gate Installation Costs in West Hollywood

Most Linear gate installations in West Hollywood fall into three buckets. Here’s what we quote, on paper, before work starts:

• Single swing-gate operator, Linear LDO50 or similar: $1,850 to $2,900 installed, including the operator, mounting brackets, wiring terminations, limit calibration, and photo documentation. Price moves based on whether the gate leaf is steel, aluminum, or ornamental iron.
• Double swing-gate operator pair, Linear LDO33 units or equivalent: $3,200 to $4,800 installed. The second operator adds labor, a second set of safety edges, and often a shared receiver rewrite.
• Sliding gate operator, Linear VS-GSLG on a prepared track: $2,600 to $4,400 installed. If the track needs leveling or the chain rail is corroded, we quote that separately in the same written estimate before we start anything.
• Full driveway gate plus Linear operator, fabricated and installed: $3,400 to $6,400 depending on gate width, material, and whether we’re working from existing posts or pouring new ones.

What moves the price: gate weight, whether an existing operator has to be removed, whether power is already at the gate, and whether you want safety edges, a keypad, or a vehicle loop added. We don’t quote blind. Call (424) 321-7416 and we’ll come out, measure, test, and hand you a written number before anyone touches a tool. Free estimates, free second opinions on any written Linear estimate from another company.

Why West Hollywood Homeowners Call Vance Gate Repair West Hollywood for Linear Work

We’re not a dealership, and we’re not tied to one brand’s parts pipeline. We work on nine automation brands, and Linear is one of them. That matters because West Hollywood properties are full of mixed installs: a Linear operator on the driveway, a LiftMaster keypad on the pedestrian gate, a DoorKing board someone added later. We fix what’s there, and we don’t push a replacement unless the unit is genuinely beyond economic repair.

Adrian Vance built this company after years of commercial access-control work, and the habit stuck: name what you found, name what it costs, name what you left behind. Every Linear job we do, from a simple board swap to a full driveway gate install, comes with a written price first, a photo record at the end, and a full year of Done Right coverage. We also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if your property has a mixed setup, we handle the whole thing in one visit. Call (424) 321-7416 and a person answers, any hour.

FAQs