FAAC Hinge & Roller Replacement Nationwide

FAAC Hinge & Roller Replacement: The West Hollywood Owner’s Guide

We stock FAAC-compatible hinge and roller replacement parts on our trucks, and most West Hollywood swing-gate jobs run between $240 and $480 installed, depending on the FAAC model and how many hinge points need attention. Same-day service is available in most cases when the gate still moves and we can match the part on the first visit. You’ll typically know this part failed when the gate starts sagging at the far corner, grinding against the ground, or shuddering as the opener strains to push it through the arc.

Call (424) 321-7416

In West Hollywood, we see this failure pattern regularly on properties along the hillside streets above Sunset, where a gate’s weight shifts as soil settles and the concrete piers shift slightly seasonally. A hinge that carried the gate fine for years suddenly carries it at a slight cant, and the roller binds against the guide track. It’s not an opener problem. It’s a load-bearing problem, and the hinge or roller is the part that absorbed it.

Which FAAC Models This Applies To

This page covers hinge and roller replacement for FAAC swing-gate operators and the gate hardware they drive, including the 400, 402, 412, 415, S418, and S450H series (the S450H on light commercial installations). The hinge itself isn’t made by FAAC; FAAC manufactures the operator, and the hinge-and-roller assembly is spec’d to match the gate’s weight and duty rating. We carry the same grade of hardware FAAC recommends in its installation manuals for each series, plus quality aftermarket equivalents when the gate predates current OEM stock.

Here’s the compatibility gotcha owners miss: an FAAC 412 and an FAAC 415 can both swing a gate, but they have different duty ratings, and the hinge and roller spec that works on one may wear out in 12 months on the other. We measure the gate leaf, weigh it, check the opener’s model plate, and match the hinge to the load, not to whatever was there before. If a previous repair put a residential-grade hinge on a 15-foot steel gate, the part failed early for a reason we can name.

Signs Your FAAC Hinge & Roller Replacement Is Failing

• The gate sags at the latch end. The top hinge pin is worn oval, or the hinge leaf has loosened from the pier. The gate now hangs a half-inch or more lower at the free-swinging corner than it did a year ago.
• A grinding or scraping sound during travel. The roller is dragging against the guide rather than rolling. In West Hollywood, the mix of dry-season dust and morning marine layer adds grit that accelerates roller wear more than inland properties see.
• The opener labors or stops mid-arc. The hinge and roller are binding, and the operator is drawing higher amperage to compensate. Left alone, the opener’s capacitor and gearbox take the long-term damage.
• Visible rust staining at the hinge pin or roller axle. Coastal-adjacent air works into cheap zinc plating in a few seasons. Once the pin rusts, every swing cycle reams the hinge bore wider.
• The gate bounces or shudders at the end of travel. A worn hinge lets the gate flex, and the roller doesn’t settle cleanly into its closed position. The opener may reverse slightly or make two attempts to close.

Before

After

Replacement Cost & What’s Included

In West Hollywood, a standard single-gate hinge and roller replacement runs $240 to $480 installed for most residential FAAC swing gates. The range depends on three things: how many hinge points need replacement (one top hinge or all three), whether the roller track needs re-anchoring, and whether the gate leaf has sagged enough that it needs jacking and realignment before the new hinge goes in.

That price includes the parts, the labor, realignment of the gate leaf, and a written price handed to you before any work starts. No surprise invoice at the end. Under the Haven Standard, every job includes a photo record of what we found and what we installed. The 365-Day Done Right Promise covers the completed work for the full year after install. If the hinge or roller fails because of our workmanship or the part itself, we fix it at no charge.

DIY or Call Us?

You can safely diagnose the problem yourself. Stand at the latch end, lift slightly: if the gate moves up more than a quarter-inch before the hinge catches, the hinge pin is worn. Open the gate and run your hand flat under the roller: if it’s scraping instead of rolling freely on the track, that’s the confirmed failure. That’s useful information for the phone call.

What you shouldn’t do is unbolt the hinge with the gate still mounted. A residential swing gate routinely weighs 300 to 800 pounds, and once the top hinge releases, that weight has to go somewhere. We use a mechanical lift to carry the leaf safely while the old hinge comes off and the new one goes on. If you’ve already loosened bolts and the gate is now hanging by one hinge, stop and call (424) 321-7416. We’ll send a technician.

FAQs